(Motor+ESC+Remote) electric skateboard mountainboard kit MTSPF7.12K 200A Supercase VESC6 VESC75300 based controller and brushless Red cover motor (non-sealed motor) and Remote
Price includes 1pcs ESC and 1pcs motor and 1pcs remote
1.Specifications of MTSPF7.12K Supercase200A ESC based on VESC6 speed controller:
| Model no | MTSPF7.12K Supercase200A | Cont. Current | 200A |
| Voltage | 3-12S | Burst Current | 250A |
| BEC | 5V | PCB size | 92*52*22 mm |
| Hardware | based onVESC75300 | Firmware version | updatable |
| PCB net weight | 160g | Aluminium Case | 98.5*55.5*35mm |
| Feature | 12pcs mosfets; 8-layer PCB; separate high current components and low-curent components to two PCBs |
2.Motor specifications
| Model No. | MTO6355-190-HA | MTO6365-200-HA | MTO6374-190-HA |
| With Hall Sensor | With Hall Sensor | With Hall Sensor | |
| KV | 190 | 200 | 190 |
| Idle Current | 1.0A | 0.8A | 0.8A |
| Max. Current | 65A | 65A | 65A |
| Input Volt | 2-12s Lipo | 2-12s Lipo | 2-12s Lipo |
| Max. Output Watt | 3510W | 3520W | 3550W |
| Max. Pull | 12000g | 9700g | 13000g |
| Rated Current | 55A | 60A | 60A |
| Motor Weight | 600g | 745g | 825g |
| Shaft | 8mm | 8mm | 8mm |
| Output shaft length | 26mm | 26mm | 26mm |
| Resistance | 0.0441 | 0.0402 | 0.0402 |
3. Specification of MTSKR20WFV2 waterproof Remote controller with screen and receiver:
| Model No. | MTSKR2005WF (MTSKR20WFV2) | Waterproof Rank | IP66 |
| Control Mode | New Esk8 | Application | Only for Electric skateboard, elongboard, mountainboard |
| Speed Display | Yes | Travel Mileage | Yes |
| Throttle and brake Display | 100% | VESC Control Mode | Duty Cycle/ Current Mode |
| Speed Mode |
3 speed modes, each mode can adjust speed from 1%-100% throttle |
Accessories | Wireless charging pad; receiver; 3pcs dupont cable |
| Charger |
QC 2.0 wireless |
Wireless Frequency | 2.4GHz wireless with 40 channels |
| Display Screen |
OLED yellow & blue screen |
Triggers | 2x high senstive triggers |
| Throttle and Brake Signal Output Range |
1.5ms-2ms for throttle; 1.5ms-1ms for brake |
Telemeter Data by Receiver | Motor RPM; main battery voltage |
| Voltage Display |
Remote & main battery voltage level (lithium iron; lithium ion battery optional) |
Telemeter Data by VESC | ESC voltage/ current/ temp; Motor temp/ RPM |
| Compatible ESCs |
VESCTOOL/ Focbox/ Other PWM ESCs that has same signal output range with the remote |
Receiver Built-in Switch for Esk8 Light / Esurf Water Pump |
1x 30V 3A mechanical relay switch; 1x 20V 2A transistor electronic switch |
MTSPF7.12K Port definations:
- USB port for programming;
- LED Port for connecting customers LED light to show ESC is on or off;
- Sensor port for motor Hall sensors (ABI, HALL, magnetic precision encoders);
- CAN Port for CAN communication with other devices and VESC arrays;
- COMM port for various kinds of other communication methods like I2C, ADC, Uart,You can use your Arduino or Raspberry Pi to control the VESC!
- PPM port to connect PPM transceivers.
Reviews
There are no reviews yet.